the Sociable Pint

The Sociable Pint at Allen Street Hardware - 11/30/09

admin — Sat, 02 Jan 2010 03:59:03 +0000

Documentation from the November 30th show at Allen Street Hardware, Buffalo, NY.

The Sociable Pint - 11/30/2009 - Allen Street Hardware Cafe from muse207 on Vimeo.

Progress in Photos

bclark — Fri, 24 Jul 2009 18:19:07 +0000

The very first prototype of the circuit.

The original 3D CAD design of the original module casing.

In order to test the capabilities of the sensors and wireless network, I experimented with few basic versions of the final circuit.

After I was satisfied with the preliminary testing and circuit design, I sent out the circuit board to be printed.

This is what the circuit looked like after I soldered on all of the components. Because I have to cram so many components underneath a little pint glass, I settled on a 3 tier design.

The completed circuit securely fitted together.

The first three glasses.

Video Clip from Dorkbot Buffalo

bclark — Fri, 24 Jul 2009 04:42:58 +0000

Footage from Dorkbot Buffalo on 2/7/2009 at Sugar City of the unveiling of the very first networked pint glass.

The Sociable Pint - the first glass (2/7/2009) from muse207 on Vimeo.

Dorkbot Photos 2/2009

admin — Thu, 23 Jul 2009 23:06:26 +0000

These photos are from my presentation at Dorkbot Buffalo at Sugar City on February 7th, 2009. (It seems like eons ago.) Thanks Al and Jessica for inviting me! Thanks Liz for the photos! I unveiled my very first pint glass at the event. Unfortunately it was a little bit lonely. It had no other glasses to talk to.

Video footage of the event to come…

PCBs - version 1

bclark — Thu, 12 Feb 2009 03:21:30 +0000

The PCB design has been submitted

bclark — Thu, 12 Feb 2009 02:58:31 +0000

I have submitted my first iteration of my circuit board design to BatchPCB for printing. Hopefully they will arrive any day now. At this point I am making 3 glasses. This will enable me to test the basic software functionality of the glasses.

It is my hope to have 12 glasses functional by the beginning of May but this completely depends on what grants I can get.

I recalculated the cost of each pint glass module and almost crapped my pants. After significantly reducing the cost of each glass, I am back up to about $250 per glass module. If I am able to produce a large amount of glasses at a time the cost will be reduced to under $100 per glass. It’s not like any individual component of the glass is that expensive. The problem is that I have many inexpensive components that add up. Add shipping, setup fees, and taxes, and I have a little financial hurdle on my hands.

Fortunately, I have left myself room in the circuit board to swap in and out the more expensive components for more inexpensive ones, so my next wave of glasses will be cheaper in price. I can solder on an ADXL330 chip instead of using the Sparkfun ADXL breakout board. I can leave out the Arduino Mini Pro module and manually solder the ATMEGA168 chip and the necessary components. These modifications will be difficult to complete and will take time (and a better soldering tip than what I have), but they will also reduce the component cost by $35 per glass. But with that being said, I really need to start making some design sacrifices.

At this time I just want to build the first iterations of glasses, complete the programming, and test them before I make any changes. I checked and rechecked my circuit board design a dozen times before I submitted it to be printed, but I am still worried about things not working perfectly. For one, I can’t properly test the effectiveness of the force sensor and the conductive film on the glass until they are completely built. Also I still am nervous about the current load of my DC-to-DC step up component. Anyway, even though this process has been painfully slow, I finally feel that I am making some real progress.

BREAKTHROUGH!!

bclark — Wed, 17 Dec 2008 22:55:11 +0000

MESH NETWORK IS NOW FUNCTIONAL!!

ALL MODULES CAN COMMUNICATE WITH ANY OTHER MODULE WITHIN SIGNAL RANGE!!

RSSI IS WORKING IN ALL MODULES TO REVEAL (approximate) PROXIMITY OF CLOSEST MODULE!!

YAY!!

(finally)

(onto the next problem)

Package Design of the Module

bclark — Sun, 09 Nov 2008 01:18:59 +0000

This is the first prototype of the housing for the electronics. It has been developed in the 3D modeling program, SolidWorks, and sent to a rapid prototyping machine to be formed.

I originally considered using the prototype as a mold to produce plastic casings. I have no experience in mold making so I consulted people with experience in this matter. I was informed that the tolerances of a 1/16 inch that I am dealing with could be problematic in the mold making process.

Considering this information, I tested the robustness of the ceramic prototype and was pleasantly surprised. I subjected the prototype to abuse (i.e. by dropping the prototype on floor, by squeezing it in a clamp) and it is apparent that it is more tolerant to strains than the pint glass that it will be affixed to.

The rapid prototyping process is relatively inexpensive (>$5 per piece), and in small quantities (>20 pieces), it seems economical to just use the ceramic prototypes instead of producing plastic versions of the casing.

I wanted to squeeze the electronics into a smaller area, but with the tools that I have access to, the casing that I have produced seems like the smallest I can go at this point. My desire was to fit everything in a 1/2 inch puck glued to the bottom of the glass, but the size of the 850 mA Li-ion battery alone makes this desire improbable. I may be able to go smaller in future iterations of this project, but for now, the size of the casing which I am using is acceptable.

Affixed to the pint glass, the image above is what the complete module will look like. Unfortunately, I have not completed the electronics that will be put inside.

I have attached a clear conductive plastic film that skirts the glass to the capacitance sensor in the glass. I have also experimented with other methods such as conductive paint. Conductive paint is opaque and it doesn’t adhere to the glass surface well. I tried creating a meshed mask and then painting on the conductive paint in attempt to give the touch surface of the glass a somewhat transparent appearance, but even covering this coat with a clear liqueur, the paint still has problems sticking to the glass.

The plastic film has achieved the best results even though it has its own problems. For one, it gets dirty really easily. Fingerprints seem to affix themselves to the plastic film quite easily. Also, liquids easily get caught in between the glass and the plastic film. I ameliorated this problem by applying a clear paint around the edges of the plastic. At this point, the conductive plastic is the best solution, but I really want to find a better solution in the future.

Xbee Modules as Proximity Sensors

bclark — Mon, 18 Aug 2008 22:31:17 +0000

For this project I want to use the Xbee modules, not only to allow the glasses to share data with each other, but also as proximity sensors. To test whether that this is a viable option, I placed two Xbee modules at specific distances from each other and took signal strength measurements over a minute. I averaged these values and graphed them.

One module was connected via USB to a computer so I could collect the antenna strength data directly to the computer. I wrote a short python program to assist me in the collection of this data.

According to this investigation, I am a little worried about using the Xbees to determine proximity. I tested the Xbee modules in an open space in a clear line of sight from each other and the signal strength values were very inconsistent. A bar situation will be much more complex because the space will contain obstructions such as people and walls. Additionally, I did not test the Xbee modules within the glasses. I plan to include capacitance sensors within these glasses which means that the glasses will be covered with a clear conductive film. The problem with this strategy, even if it works well with the capacitance sensors, is that the film may dampen the signals sent between the glasses.

In a perfect world, it is my hope to eventually find a way to accurately measure distance between glasses so I can use triangulation to map out the location and movement of the glasses within the bar space. Currently, I can tell whether two glasses are within 5 feet of each other through signal strength. At the moment I plan to integrate close proximity events like this into my project.

I have not found a way to determine signal strength between the modules without putting the Xbees into command mode. This is incredibly undesirable because I want to be constantly collecting and sharing accelerometer data and I can not do this when the Xbee is in command mode.

Sketching Out the Shell

bclark — Sat, 16 Aug 2008 22:38:02 +0000

Working out the shape of the shell that needed to be affixed to the pint glass, I started to sketch out a design on paper that I would later draft in SolidWorks.

Through this process I had to work out a number of problems. The most important problem was how I was going to fit all of the electronic components underneath the glass. I needed to create a design that maximized space of the components. I also had to pay attention to how the design would allow for the placement of a RGB LED and that would allow for easy accessibility if I needed to open it up and change things around. The package design also needed to be robust in case it is dropped and stable so the glass wouldn’t be at risk of falling over.